CPU: Atmel ATSAMD21J18
CPU Speed: 48 MHz
Operating Voltage: 3.3 V
Analog In/Out: 8/1
Flash Memory: 256 KB
SRAM: 32 KB
Danyboard smartBLE is an open-source electronics prototyping platform. Danyboard smartBLE is designed to provide an efficient, fast, simple and cost effective solution to create IoT and wearable devices.
It is equipped with:
- MCU Atmel SAMD21J18A 32bit ARM Cortex M0+
- Bluetooth BLE v4.1
- MicroSD Reader
- Temperature sensor
- EEPROM 256KB
- Li-Po charger
The board includes a Li-Po charging circuit that allows the danyboard smartBLE to run on battery power or external 5V, charging the Li-Po battery while running on external power. Switching from one source to the other is done automatically.
Warning: The Danyboard smartBLE runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.
You can find in the Getting Started section all the information you need to configure your board, use the Arduino Software (IDE), and start tinker with coding and electronics.
|Microcontroller||ATSAMD21J18A, 32-bit ARM Cortex M0+|
|Board Power Supply||3.3 – 5 V (USB, VIN)|
|Flash Memory||256 KB|
|Digital I/O Pins||25, with 10 PWM|
|Analog Input Pins||8, 12-bit ADC channels|
|Analog Output Pin||1, 10-bit DAC channel|
|External Interrupts||All pins except pins 2 and 4|
|DC Current per I/O Pin||7 mA|
|Clock Speed||48 MHz|
|Supported Battery||Li-Po Single Cell 3.7 V|
|Bluetooth||BLE v4.1 2.4 GHz|
|Sensors||Accelerometer, Gyroscope and Temperature|
|Full-Speed USB Device and embedded Host|
The Danyboard smartBLE is open-source hardware! You can build your own board using the following files:
ARM Core Benefits
The Danyboard smartBLE has a 32-bit ARM core that can outperform typical 8-bit microcontroller boards. The most significant differences are:
- 32-bit core that allows operations on 4 byte wide data within a single CPU clock.
- CPU Clock at 48MHz
- 12 channels DMA controller that can relieve the CPU from doing memory intensive tasks
- 32 bit Real Time Counter (RTC) with clock/calendar function
- 32 bit CRC generator
- Two-channel Inter IC Sound (I2S) interface
- Peripheral Touch Controller (PTC)
For further information about the SAM-D21 microcontroller please refer to the datasheet.
Li-Po batteries, Pins and board LEDs
Li-Po batteries are charged up to 4,2V with a current that is usually half of the nominal capacity (C/2). For Danyboard M0 we use a specialized chip that has a preset charging current of 256 mAh. This means that the MINIMUM capacity of the Li-Po battery should be 500 mAh. Smaller cells will be damaged by this current and may overheat, develop internal gasses and explode, setting on fire the surroundings. We strongly recommend that you select a Li-Po battery of at least 500 mAh capacity. A bigger cell will take more time to charge, but won’t be harmed or overheated.
If you want to connect a battery to your smartBLE board be sure to search one with female 2 pin JST PHR2 Type connector.
Polarity : looking at the board connector pins, polarity is Left = Positive, Right = GND
Download here the Connector datasheet. On the M0 board, connector is a Male 2pin JST PH Type.
Note : DO NOT CONNECT to the male JST connector present on the board anything else than a Li-Po battery whose characteristics are compliant with those indicated above. Please DO NOT POWER VIN with more than 5V.
This pin can be used to power the board with a regulated 5V source. If the power is fed through this pin, the USB power source is disconnected. This is the only way you can supply 5v (range is 5V to maximum 6V) to the board not using USB.
This pin outputs 5V from the the board when powered from the USB connector or from the Battery pin. It is unregulated and the voltage is taken directly from the inputs. When powered from battery it supplies around 3.7 V.
This pin outputs 3.3V through the on-board voltage regulator. This voltage is the same regardless the power source used (USB, Vin and Battery).
The CHARGE LED on the board is driven by the charger chip that monitors the current drawn by the Li-Po battery while charging. Usually it will lit up when the board gets 5V from VIN or USB and the chip starts charging the Li-Po battery connected to the JST connector.
There are several occasions where this LED will start to blink at a frequency of about 2Hz. This flashing is caused by the following conditions maintained for a long time (from 20 to 70 minutes):
- No battery is connected to JST connector.
- Overdischarged/damaged battery is connected. It can’t be recharged.
- A fully charged battery is put through another unnecessary charging cycle. This is done disconnecting and reconnecting either VIN or the battery itself while VIN is connected.
On Danyboard smartBLE the onboard LED is connected to LED_BUILTIN.